REINFORCED CEMENT CONCRETE (R.C.C.)

REINFORCED CEMENT CONCRETE (R.C.C.)

 Concrete is good in resisting compression but is very weak in resisting tension. Hence reinforcement is provided in the concrete wherever tensile stress is expected. The best reinforcement is steel, since
tensile strength of steel is quite high and the bond between steel and concrete is good. As the elastic
modulus of steel is high, for the same extension the force resisted by steel is high compared to concrete. However in tensile zone, hair cracks in concrete are unavoidable. Reinforcements are usually in the form of mild steel or ribbed steel bars of 6 mm to 32 mm diameter. A cage of reinforcements is prepared as per the design requirements, kept in a form work and then green concrete is poured. After the concrete hardens, the form work is removed. The composite material of steel and concrete now called R.C.C. acts as a structural member and can resist tensile as well as compressive stresses very well.

 Properties of R.C.C./Requirement of Good R.C.C.

1. It should be capable of resisting expected tensile, compressive, bending and shear forces.
2. It should not show excessive deflection and spoil serviceability requirement.
3. There should be proper cover to the reinforcement, so that the corrossion is prevented.
4. The hair cracks developed should be within the permissible limit.
5. It is a good fire resistant material.

6. When it is fresh, it can be moulded to any desired shape and size.
7. Durability is very good.
8. R.C.C. structure can be designed to take any load.

Uses of R.C.C.
It is a widely used building material. Some of its important uses are listed below:
1. R.C.C. is used as a structural element, the common structural elements in a building where
R.C.C. is used are:
(a) Footings (b) Columns
(c) Beams and lintels (d) Chejjas, roofs and slabs. (e) Stairs.

2. R.C.C. is used for the construction of storage structures like
(a) Water tanks (b) Dams (c) Bins (d) Silos and bunkers.

3. It is used for the construction of big structures like
(a) Bridges (b) Retaining walls (c) Docks and harbours (d) Under water structures.

4. It is used for pre-casting (a) Railway sleepers (b) Electric poles

5. R.C.C. is used for constructing tall structures like
(a) Multistorey buildings (b) Chimneys (c) Towers.

6. It is used for paving
(a) Roads (b) Airports.

7. R.C.C. is used in building atomic plants to prevent danger of radiation. For this purpose
R.C.C. walls built are 1.5 m to 2.0 m thick.

Comments

Post a Comment

Popular posts from this blog

Particle-Size Analysis of Soils ASTM D422

Particle-Size Analysis of Soils  ASTM D422 GRAIN SIZE ANALYSIS SIEVE & HYDROMETER ANALYSIS Purpose : This test is performed to determine the percentage of different grain sizes contained within a soil. The mechanical or sieve analysis is performed to determine the distribution of the coarser, larger-sized particles, and the hydrometer method is used to determine the distribution of the finer particles. Standard Reference : ASTM D 422 - Standard Test Method for Particle-Size Analysis of Soils Significance : The distribution of different grain sizes affects the engineering properties of soil. Grain size analysis provides the grain size distribution, and it is required in classifying the soil. Equipment : Balance, Set of sieves, Cleaning brush, Sieve shaker, Mixer (blender), 152H Hydrometer, Sedimentation cylinder, Control cylinder, Thermometer, Beaker, Timing device. Test Procedure: Sieve Analysis: (1) Write down the weight of each sieve as
Read more

Compressive Strength of Concrete Cylinder [Urdu/Hindi] Part-3 ASTM C39/AASHTO T22

Image
Compressive Strength of Concrete Cylinder [Urdu/Hindi] Part-3 ASTM C39/AASHTO T22 *Scope* This test method covers determination of compressive strength of cylindrical concrete specimens such as molded cylinders and drilled cores. It is limited to concrete having a density in excess of 800 kg/m3 [50 lb/ft3]. The program requires a working knowledge of the following ASTM test methods and practices. Referenced Documents. • C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field • C42/C42M Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete • C192/C192M Practice for Making and Curing Concrete Test Specimens in the Laboratory • C617 Practice for Capping Cylindrical Concrete Specimens • C670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials • C873 Test Method for Compressive Strength of Concrete Cylinders Cast in Place in Cylindrical Molds • C1077 Prac
Read more

Slump Test of Concrete ASTM C143 [Urdu & Hindi]

Image
Slump Test of Concrete ASTM C143 [Urdu & Hindi] *Scope* The concrete slump test measures the consistency of fresh concrete before it sets. It is performed to check the workability of freshly made concrete, and therefore the ease with which concrete flows. It can also be used as an indicator of an improperly mixed batch. The test is popular due to the simplicity of apparatus used and simple procedure. The slump test is used to ensure uniformity for different loads of concrete under field conditions. The program requires a working knowledge of the following ASTM test methods and practices. Referenced Documents ASTM Standards: • C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field. • C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete. • C172 Practice for Sampling Freshly Mixed Concrete. • C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method. • C231 Test Method for Air Con
Read more